11051 Road Starquad cable with PUR Jacket
|GAC-4/1 (11051) Road Starquad balanced audio cable,
New Product available in September 2016
Starquad cable similar to our 11001 but enforced with another jacket layer with ultrastrong PUR Material.
Additional shielding together with our double reussen shield with the useage of our conductive fiber coating known and used on our Hi-End wire 11301 and 10561.
|Gotham "Star-Quad" cables are the most advanced microphone cables presently available. We have combined an ultraflexible PVC-jacket, low capacitive PE insulation, "double Reussen shielding" and quad (4-conductor) construction for a truly professional cable at an affordable price. The "Star-Quad" concept is known and recommended where the RF-rejection is the most important factor and where very long cable runs are needed. As we use each 2 conductors for low and high signal, we reduce the signal loss by 50% and due to the offset of the incoming RF-signal by the way the 4 conductors are twisted, the RF-rejection is over 130dB (25 kHz). The exclusive double shielding does its part of these features as well.
LFOC higher grade copper at best standards for best performance.
|1 = PUR -Jacket:||PUR, Ø 7.0 mm / 0.28 in, velvet black 0.70mm / 0.028in|
|2 = PVC-Jacket||PVC, Ø 5.6 mm / 0.22 in, white (ultrasoft) 0.80mm / 0.031in|
|3 = Shield No. 1||Bare copper wires (0.10 mm / 38 AWG) 100% coverage|
|4 = Shield No. 2||Bare copper wires (0.10 mm / 38 AWG) 100% coverage|
|5 = Conductive Viscose fiber coat:||PETPAL Polyester nonwoven thermally bonded,
both sides aluminium coated. Counter wrapped to the quad twisted conductors
|6 = Twisting||Four core and cotton yarns twisted together, star-quad|
|7= Insulation (cond):||PP -9Y , Ø 1.4 mm / 0.055in, white, ivory, pink and red,|
|8 = Conductor:||Stranded bare copper wires 28x0,10mm / 28x38AWG OFC Ø 0.60mm (0.28 mm²) /23 AWG (23AWG)|
|Conductor resistance:||< 88 ohm/km / < 26.8 Ohm/1000ft|
|Shielding resistance:||< tba Ohm/km|
|Capacitance:||cond/cond:||< TBA nF/km|
|cond/shield:||< TBA nF/km|
|Side circuit capacitance:||single conductor||TBA pF/m|
|Side circuit capacitance:||Quad system||TBA pF/m|
|Noise attenuation:||130 dB (see wiring)|
|Characteristic impedance:||at 20 kHz:||180 Ohm|
|Test voltage:||cond/cond:||500 veff|
|Operating voltage||low voltage 100v max|
|Temperature range:||flexi-installed:||-5° to +50° C|
|fix-installed:||-30° to +70° C|
|11001||GAC-4/1||5.4 mm / 0.21 in||black||100m / 328ft||4.70 kg / 10.36 lbs||4x100m|
|11051||GAC-4/1 Road||7.0 mm / 0.28 in||black||200m / 656ft||TBA||2x200m|
|11201||GAC-4/1 FRNC||5.4 mm / 0.21 in||black||100m / 328ft||4.70 kg / 10.36 lbs||4x100m|
Factory direct orders accepted. No minimum order! Simply inquire per email
please ask for a quotation here: (link)
please ask for a quotation here: (link)
Starquad wiring instruction:
In order to benefit from the Starquad concept you need to wire the 4 conductors for you balanced audio cable as follows: (See wiring diagram below)
Bundle each opposite (Star) conductor together, we made colour code easy to identify the opposite conductor. (red/pink and white/ivory each belong together.)
Pin2= red&pink (Signal+), Pin3= white&ivory (Signal -). Pin1= shield 1&2 =Ground
Put each a few strands of each layer of the shields together to ground Pin 1 should you not have space for all shielding strands.
Cut away any spare strands from the shields and secure that no loose strands are hanging around. Use a shrinking tube to avoid short circuits.
We do not recommend putting any ground to the body shell on either side of your XLR line. The connector shell will get to ground once plugged into a receptacle.
RCA/Phono/Jack unbalanced wiring:
Many clients use our 4 conductor cable also for unbalanced interconnects. In this case we recommend to only use 2 conductor (red/pink) for your signal and put all other wires or parts thereof to ground with the shields. This will increase your noise protection! However for unbalanced application we do have our perfect unbalanced wires 1001x, and 1000x.
Stereo & 2 Channels application:
We actually do not support the idea to use a Starquad cable for stereo wiring, however it will be done and can be made with acceptable compromise regarding crosstalk and similar. If you use the cable as stereo line, use red/white for channel 1 and pink/ivory for channel 2. And again, all the shields to ground but not to the body shell of your connector.
Check our perfect stereo cables 12001/13001 or our conductor shielded Starquad 11301 for real quality stereo wiring!